Diodes & Transistors Rectifier Diodes · MDD

1N4007 · 1000 V 1 A General-Purpose Rectifier Diode

1N4007 is a 1000 V, 1 A rectifier diode in DO-41. Use it for mains-frequency rectification and general reverse-polarity or freewheeling duty, then verify surge current, thermal conditions and recovery speed. It is not a fast-recovery or Schottky rectifier for high-frequency switching stages.

1N4007 1000 V 1 A General-Purpose Rectifier Diode
Part number1N4007
ManufacturerMDD
Description1000 V 1 A General-Purpose Rectifier Diode
PackageDO-41
CategoryDiodes & Transistors / Rectifier Diodes
Reference priceUS$0.0070
Min. order1 pcs
AvailabilityIn stock
Reference stock718 pcs

1N4007 price and stock (reference)

QuantityReference unit priceLead time
1 pcs and upUS$0.0070In stock
500 pcs and upUS$0.0056In stock
5000 pcs and upUS$0.0035In stock

1N4007 specifications

Reverse Voltage Rating1000V
Forward Current1A
Forward Voltage1.1V @1A
RoHSCompliant

About the 1000 V 1 A General-Purpose Rectifier Diode

The classic general-purpose mains rectifier in a DO-41 through-hole package: 1 A / 1000 V, found in virtually every 50/60 Hz rectifier stage and power adapter. Check current and speed when selecting: 1 A average rectified current and 1000 V reverse voltage give far more surge capability than small-signal SMD diodes, suiting transformer-fed rectification, reverse-polarity protection and freewheeling — but it is a slow-recovery part, so do not use it on the secondary side of a switching supply; choose a Schottky there instead (1N5819, SS34). The SMD equivalents are the M7 and S1M (SMA/SMB) if you need to save board space. Through-hole parts are easy to hand-solder for prototypes and repairs; buy by the box or on tape, with batch and brand confirmed by quotation.

Replacement checks:
  • Keep the peak reverse voltage below 1000 V and leave margin for mains transients and surges.
  • Check the 1 A rating against average current, startup surge and junction temperature, not steady-state load alone.
  • Use it for mains-frequency rectification, reverse-polarity protection or general freewheeling; evaluate fast-recovery or Schottky parts for high-frequency switching.
  • When moving to SMD M7 or S1M equivalents, compare surge rating, thermal behaviour and the PCB footprint.
Direct answer: 1N4007 is a 1000 V, 1 A general-purpose rectifier in a DO-41 package with a listed 1.1 V forward drop at 1 A. It is intended for 50/60 Hz rectification, reverse-polarity protection and general freewheeling, not high-frequency switching rectification; recovery time, switching loss and operating frequency must be checked separately. Reviewed 2026-11-20

1N4007 — frequently asked questions

Can 1N4007 be used for the secondary rectifier of a switching supply?

Not directly. It is a general-purpose mains-frequency rectifier with relatively slow recovery; select a fast-recovery or Schottky diode based on frequency, output current and loss.

Is the 1 A rating an absolute maximum current?

No. It is a rated forward current under specified conditions and is also limited by surge current, heatsinking, ambient temperature and mounting.

Can M7 or S1M replace 1N4007?

They are possible SMD candidates, but reverse voltage, forward current, surge capability and footprint must all be checked; the 1 A/1000 V headline is not enough.

Related Rectifier Diodes parts

Need 1N4007?

Genuine parts · small-batch trial runs · full BOM kitting

How to order 1N4007

Send the quantity and the destination country; sales normally responds within two working hours with the unit price, date code, MOQ (1 pcs) and shipping cost. A formal full-BOM quotation normally follows within 24 hours. Shipping is quoted together with the parts.

Related pages

About pricing and stock: Prices, quantities and lead times shown on this page are for reference only. Component pricing fluctuates and we carry a very large number of part numbers — please confirm with our sales team for a firm quotation.