Resistors Shunt Resistors · BOURNS

CRF2512-FZ-R005ELF · 5 mOhm 1% 2 W Current-Sense Shunt Resistor, 2512

CRF2512-FZ-R005ELF is a 5 mOhm, 1%, 2 W current-sense resistor in a 2512 package with 50 ppm/C and current-sense/AEC-Q200 features shown in the listing. At 10 A it develops 50 mV and 0.5 W; those are calculations from resistance, not guaranteed application ratings. Confirm derating, Kelvin layout, pulse requirements and amplifier headroom before production.

CRF2512-FZ-R005ELF 5 mOhm 1% 2 W Current-Sense Shunt Resistor, 2512
Part numberCRF2512-FZ-R005ELF
ManufacturerBOURNS
Description5 mOhm 1% 2 W Current-Sense Shunt Resistor, 2512
Package2512
CategoryResistors / Shunt Resistors
Reference priceUS$0.257
Min. order100 pcs
AvailabilityIn stock
Reference stock200 pcs

CRF2512-FZ-R005ELF price and stock (reference)

QuantityReference unit priceLead time
1 pcs and upUS$0.257In stock
10 pcs and upUS$0.199In stock
30 pcs and upUS$0.175In stock
100 pcs and upUS$0.144In stock
500 pcs and upUS$0.130In stock

CRF2512-FZ-R005ELF specifications

Resistance5 mOhms
Tolerance±1%
Power Rating2W
CompositionMetal Element
FeaturesAutomotive AEC-Q200, Current Sense, Mois
Dielectric±50ppm/°C
Operating Temperature-55°C ~ 170°C

About the 5 mOhm 1% 2 W Current-Sense Shunt Resistor, 2512

CRF2512-FZ-R005ELF is a Bourns 2512 metal-element current-sense resistor listed at 5 mOhm, 1%, 2 W and 50 ppm/C over -55 to 170 C, with current-sense, AEC-Q200 and moisture-related features recorded on the page. It converts current into a voltage across its terminals and suits sensing in DC-DC, battery-management and motor-drive paths. The 2 W figure is a power rating, not a 20 A continuous-current rating that can be used without derating. Near the limit, thermal design must account for ambient, copper, pulse energy and the allowed sense voltage. Replacement checks include tolerance, temperature coefficient, power, size, low thermal EMF, pads and Kelvin sensing, not only 5 mOhm.

Replacement checks:
  • Calculate the sense voltage from 5 mOhm and the allowed burden, for example 50 mV and 0.5 W at 10 A, then verify amplifier range, gain and noise.
  • Treat 2 W as a dissipation limit rather than a current rating, and derate for ambient, copper area, nearby heat sources and long-term drift.
  • Use Kelvin sense traces so the high-current path and voltage-sense points are separated and solder or copper resistance is not added to the 5 mOhm element.
  • Check 1%, 50 ppm/C, low thermal EMF, pulse energy and the applicable AEC-Q200 scope. A substitute also needs the same 2512 pad and thermal arrangement.
Direct answer: CRF2512-FZ-R005ELF is a 5 mOhm, 1%, 2 W, 50 ppm/C current-sense resistor in a 2512 package with current-sense and AEC-Q200 features listed. The 2 W rating is not a 20 A continuous-current rating: at 20 A the calculated dissipation is already 2 W with no margin. Verify derating, copper spreading, pulse energy and amplifier input range, and use Kelvin sensing to reduce trace error. Reviewed 2026-11-20

CRF2512-FZ-R005ELF — frequently asked questions

Can a 2 W, 5 mOhm resistor carry 20 A continuously?

That cannot be concluded. At 20 A the calculated I²R dissipation is already 2 W, leaving no margin for temperature rise or long-term drift. The real continuous current must be established from temperature, copper, derating and error limits.

Why is Kelvin sensing important when the resistance is already 5 mOhm?

The measured voltage includes the voltage between the actual sense points. High-current traces and solder resistance can add a large error to a very small signal, so Kelvin routing places the sense points on the effective element.

Can any 2512 resistor with the same resistance replace it?

No. Also compare tolerance, temperature coefficient, power, low thermal EMF, pulse capability, construction and AEC-Q200 scope. An ordinary 5 mOhm thick-film part may not provide the same sensing stability.

Related Shunt Resistors parts

Need CRF2512-FZ-R005ELF?

Genuine parts · small-batch trial runs · full BOM kitting

How to order CRF2512-FZ-R005ELF

Send the quantity and the destination country; sales normally responds within two working hours with the unit price, date code, MOQ (100 pcs) and shipping cost. A formal full-BOM quotation normally follows within 24 hours. Shipping is quoted together with the parts.

Related pages

About pricing and stock: Prices, quantities and lead times shown on this page are for reference only. Component pricing fluctuates and we carry a very large number of part numbers — please confirm with our sales team for a firm quotation.