Crystals & Sensors Temperature Sensors · Aosong

AHT20 · Temperature & Humidity Sensor ±2%RH

AHT20 (Temperature & Humidity Sensor ±2%RH from Aosong) comes in a SMD 3×3mm package. Reference unit price: US$0.641, minimum order 1 piece. Availability: In stock. Shenzhen Kewei Technology Co., Ltd. supplies this part from Huaqiangbei, Shenzhen, with tiered pricing, small-batch support and full BOM kitting. Prices and lead times are confirmed on inquiry.

AHT20 Temperature & Humidity Sensor ±2%RH
Part numberAHT20
ManufacturerAosong
DescriptionTemperature & Humidity Sensor ±2%RH
PackageSMD 3×3mm
CategoryCrystals & Sensors / Temperature Sensors
Reference priceUS$0.641
Min. order1 pcs
AvailabilityIn stock
Reference stock10,684 pcs

AHT20 price and stock (reference)

QuantityReference unit priceLead time
1 pcs and upUS$0.641In stock
10 pcs and upUS$0.546In stock
30 pcs and upUS$0.480In stock
100 pcs and upUS$0.425In stock
500 pcs and upUS$0.360In stock
1000 pcs and upUS$0.351In stock

AHT20 specifications

Humidity Accuracy±2%RH
Temperature Accuracy±0.3℃
InterfacesI²C
RoHSCompliant

About the Temperature & Humidity Sensor ±2%RH

One of the most widely used domestic temperature/humidity sensors: 3×3 mm SMD package with an I²C interface, ±2%RH humidity accuracy and ±0.3 °C temperature accuracy, common in environmental monitoring, cold-chain logging, warehouse and server-room monitoring, and smart home devices. Three selection points: (1) interface and supply — two wires read the data, mostly at 3.3 V, so check levels if you drive it from a 5 V MCU; (2) accuracy and long-term drift — humidity sensors drift over time and need periodic calibration, or choose a part with built-in heater/dehumidification; (3) package and soldering — a 3×3 mm package demands good reflow control, and hand soldering can damage the sensitive internal film. Alternatives: the SHT30, SHT31 and SHT20 are common equivalents, but verify footprint and protocol before swapping. Buying note: these sensors are sensitive to storage conditions — keep them in original packaging, moisture-proof; batch confirmed by quotation.

Replacement checks:
  • Confirm host supply and I2C logic levels. Do not transfer a breakout board's 5 V capability to the bare sensor without checking absolute maximum ratings and pull-up voltage.
  • A humidity sensor needs air exchange with the outside environment. Enclosure openings, membranes, condensation and dust can change the reading; do not coat the sensing opening with ordinary conformal coating.
  • Soldering, cleaning and long storage can shift humidity accuracy. Follow the datasheet reflow and bake conditions, and validate low-humidity, high-humidity and temperature-cycle behavior before production.
Direct answer: AHT20 is a digital temperature and humidity sensor from ASAIR. The listed site data shows ±2%RH humidity accuracy, ±0.3 C temperature accuracy, an I2C interface and a 3 x 3 mm SMD package. It is intended for board-level environmental sensing, not as a waterproof probe. Verify supply and I/O levels, the sensing opening and enclosure, condensation and contamination protection, reflow and storage conditions, and whether a protective membrane or filter is required. Reviewed 2026-11-20

AHT20 — frequently asked questions

Is AHT20 waterproof?

AHT20 is a board-level sensor, not a waterproof probe. A water-resistant design normally needs a separate cavity with a breathable membrane or a finished probe, followed by condensation and response-time testing.

Can AHT20 replace SHT30 directly?

Not by function alone. Both are temperature and humidity sensors, but package dimensions, pinout, I2C timing, registers and accuracy specifications must be checked individually.

Why does AHT20 show a large reading offset?

Check supply, bus pull-ups, post-solder cleaning, enclosure openings and condensation first. Humidity sensors require stabilisation and calibration; a reading immediately after soldering is not a reliable steady-state value.

Related Temperature Sensors parts

Need AHT20?

Genuine parts · small-batch trial runs · full BOM kitting

How to order AHT20

Send the quantity and the destination country; sales normally responds within two working hours with the unit price, date code, MOQ (1 pcs) and shipping cost. A formal full-BOM quotation normally follows within 24 hours. Shipping is quoted together with the parts.

Related pages

About pricing and stock: Prices, quantities and lead times shown on this page are for reference only. Component pricing fluctuates and we carry a very large number of part numbers — please confirm with our sales team for a firm quotation.