Selection Guide Kewei Technology Engineering Team · Kewei Technology industry research

ICM-42688-P vs ICM-45686: Choosing a Six-Axis IMU Beyond Price

Both TDK InvenSense parts are six-axis IMUs in an LGA-14 outline, but the listed accelerometer range, FIFO, standby current, reference price and stock differ. This note separates directly comparable fields from data that still requires the exact datasheet.

Direct answer: For higher accelerometer range, FIFO and low standby current, ICM-45686 is the first sample candidate. For an existing ±16g and ±2000dps design, ICM-42688-P is closer to the known requirement. Both require checks for interface, supply, gyroscope range, noise, registers and pinout; the family name is not a replacement guarantee.

Full article

The same IMU family and the same LGA-14 outline do not make two parts interchangeable. In the last seven days, the site recorded a real browsing path across `ICM-42688-P`, `ICM-45686` and the motion-sensor category. That is a comparison signal, not proof that either part is the right replacement. The notes below use only fields currently visible on the Kewei product pages and separate them from data that still needs the exact datasheet.

What the two pages establish

The ICM-42688-P page lists X, Y and Z accelerometer axes to ±16g, X, Y and Z gyroscope axes to ±2000dps, an LGA-14 package, a reference price of US$15.78, MOQ 1 and reference stock of 500 pieces. The ICM-45686 page lists X, Y and Z accelerometer axes to ±32g, 16-bit output, an 8KB FIFO, 2.2 uA standby current, an LGA-14 (3 x 2.5 mm) package, a reference price of US$9.62, MOQ 1 and reference stock of 691 pieces.

Those fields are enough to decide which part deserves a sample. They are not enough to declare a drop-in replacement. Neither page gives a complete interface, supply range, gyroscope range, noise, output-data-rate, register map or pin definition. A shared family name cannot fill those gaps.

Range: ±32g is not an automatic replacement for ±16g

A ±32g range can cover greater shock or vibration, but a wider full-scale range does not automatically mean better accuracy. The useful comparison is noise density, resolution, bias stability and drift within the range the product actually uses.

If a design is already calibrated around ±16g and ±2000dps, changing the full-scale range changes scale factors and register data. If the current ±16g channel is saturating, a higher-g part is a sensible candidate, but the gyroscope range and bandwidth still need confirmation.

FIFO and standby current affect the sampling architecture

The ICM-45686 page lists an 8KB FIFO and 2.2 uA standby current. Those fields can matter for low-power and intermittent sampling because they reduce host wake-ups. The ICM-42688-P page does not list FIFO depth or standby current, so it would be wrong to infer either value from the family.

Engineering should evaluate sample rate, batch size, FIFO overflow, host wake-up frequency and battery life together. A standby-current headline is not enough: active current, gyroscope state, bus rate and duty cycle determine the product's real power consumption.

Price and stock describe the current quote, not performance

The page references are US$15.78 for ICM-42688-P and US$9.62 for ICM-45686, with reference stock of 500 and 691 pieces, both MOQ 1. Price is useful for sample budgeting but does not establish performance, quality or long-term supply.

Before production, confirm the complete ordering code, lot and date code, package dimensions, pads, reflow profile and lead time. MEMS parts are sensitive to board flex, soldering stress and mounting position. A sample working on one board is not proof that volume assembly will be stable.

Interface, registers and footprint must be checked

Both parts require checks for host interface, supply, power sequence, register addresses, data format, FIFO behaviour and interrupt logic. Even when both packages are called LGA-14, dimensions and pads may differ, and pin definitions cannot be inferred from the family name.

If the goal is to find a new candidate, start from the actual requirement: range, bandwidth, noise, power, interface, footprint, firmware and certification. Do not buy the cheaper part first and force the firmware and mechanics to compensate.

How to submit the comparison

Send the current part number, target accelerometer and gyroscope range, host interface, supply, sample rate, quantity per build, annual demand and project stage. For qualification, buy a small sample batch and verify soldering, registers, noise, drift and end-product output before adding the part to the BOM.

Conclusion

The visible data makes ICM-45686 a candidate for higher-g, FIFO and low-standby evaluation, while ICM-42688-P fits projects that already have ±16g and ±2000dps requirements and need exact verification. Neither can be replaced from the TDK InvenSense name, six axes and LGA-14 outline alone. Check the exact datasheet and pinout first, then validate a sample in the real product.

Kewei's take: what this means for procurement

Industry-level changes end up in individual purchasing decisions: lead time, price, alternatives. Following them regularly beats firefighting.

Related component categories

For the component categories covered by this story we keep the common part numbers in stock. Browse by category, or send us your part list and we will quote the whole BOM.

Related parts in stock

All part numbers above are in stock or in transit. Order directly, or submit a BOM and we will match and quote it.

Need these components?

Authentic parts · Same-day shipping · Prototype and volume quantities

More articles